Short answer
To judge fogging equipment, first check that the product label allows the way the device applies it. Ask what proof backs up claims about coverage. Confirm how wet time and going back in are handled. Then compare the whole process, including cleaning and downtime, with simple wiping. Newer gear can help in some settings. But no device replaces cleaning first or following the label.
Why brochures are a poor guide
Disinfecting gear is sold with striking pictures. Blue mist wraps around a chair. A robot bathes a hospital room in violet light. A drone glides over stadium seats. Those pictures are made to suggest total coverage. They rarely show you what really landed on the surfaces, if it stayed wet long enough, or if the room was clean to begin with.
The fast growth of the field after 2020 made the problem harder. New devices appeared quickly. Older ones were repackaged. Many buyers had nothing to compare them with. Some equipment has solid proof behind it in certain settings. Some does not.
You do not need to be an engineer to judge these tools. You need a short set of questions. You also need to be willing to ask for proof and not just praise.
The first question for any device
Does the product label allow this way of applying it? A disinfectant should be fogged, sprayed with an electrostatic sprayer, or spread by drone only where its own label gives directions for that method.
That puts the label ahead of the machine. Take an advanced electrostatic sprayer loaded with a product that has no electrostatic directions. It is not a method that follows the label, however good the hardware is. The disinfectant's germ-killing claims were proven under set conditions. Changing how it is applied can change whether those claims hold.
So before you judge the equipment, ask which product will go in it, and read the label. If the answer is vague, the rest of your review does not matter much.
Electrostatic sprayers vs ULV and thermal foggers
These devices all turn liquid into droplets. They differ in droplet size and in how they deliver it. Ultra-low-volume foggers, called ULV, make fine droplets that hang in the air and spread widely. Thermal foggers use heat to make even finer particles. Electrostatic sprayers make somewhat larger droplets and give them an electric charge, so they are drawn to surfaces.
Look hard at claims about coverage. In EPA testing published in PLOS ONE in 2021, most devices produced droplets of 40 microns or larger and showed minimal wrap-around deposition on an 8-inch cylinder. The researchers tested six electrostatic sprayers, two foggers, and a garden sprayer. A micron is a tiny unit of size. In plain terms, the back sides of objects got much less product than ads often suggest.
That does not make the devices useless. It means technique matters. A good crew comes at surfaces from more than one side and keeps the right distance. They confirm that treated surfaces stay wet for the contact time on the label. A company that describes how it does this is showing you more skill than one that leans on the word wrap-around.
- ULV fogger: fine droplets, wide spread, longer time hanging in the air.
- Thermal fogger: very fine particles, usually for empty spaces only.
- Electrostatic sprayer: larger charged droplets, aimed by the operator.
- All three: depend on the label, cleaning first, and the wet time.
Hydrogen peroxide vapor and dry-fog systems
Some systems spread hydrogen peroxide as a vapor or a very fine dry fog in a sealed room. You will see these more often in healthcare. They are sometimes used after a patient with a certain infection leaves a room. They usually require sealing vents and doors, tracking the level in the air, and airing out the room before anyone goes back in.
The trade-off is time. Sealing a room, filling it, and airing it out takes far longer than cleaning it by hand. That kind of downtime may be fine for a high-risk room in a hospital. It is harder to justify for a routine office.
If a company offers a sealed-room system, ask about the product's registration and label. Ask how the room is sealed and how the level in the air is tracked. Ask how they confirm it is safe to go back in, and how long your space will be out of use.
UV-C robots, drones, ionizers, and ozone
UV-C is a kind of ultraviolet light. It can inactivate germs on surfaces it reaches directly, if the light is strong enough and shines long enough. Handheld wands and room-size robots are both on the market. UV-C is not a chemical fog, but it is often sold along with fogging as a no-touch choice.
Its main limit is shadows. Surfaces blocked from the light get little or no dose. Think of the underside of a table or the back of a keyboard. Distance also matters, because the light weakens quickly as the lamp moves away. And UV-C does not remove dirt.
Studies that compare no-touch methods with careful wiping by hand often find that wiping holds up well. That is most true when the no-touch device is used on surfaces that were never cleaned. Keep that pattern in mind for any quote that offers UV-C as a swap for your cleaning staff and not an addition to it. UV-C devices also need strict safety controls, since direct exposure can harm skin and eyes. Ask how the device stops itself from running while people are present.
If you do look at UV-C, ask for the device's dose at a stated distance and how long it runs in each position. Ask how many positions a room needs to cut down on shadows. Ask how the operator confirms that every key surface was in the line of sight at least once.
Drones have been offered for spraying large outdoor venues and arenas. They face the same label question as any other spraying method. They also raise practical questions about drift, reaching the undersides of seats, and safety around structures. Ask for the label directions and for proof from similar venues before you consider them.
Air ionizers and other air cleaning devices are sometimes bundled into disinfecting quotes. They treat the air. They do not disinfect surfaces, and you should judge their claims separately. Be extra careful with ozone generators. Ozone levels that are safe for people do not work against germs and mold in indoor air.
Can the technology be tied to a label, a recognized test, or a clear way of working? If not, keep it out of your disinfecting plan until it can.
Three proposals for one school district
Here is an example comparison, for illustration. A small school district asks three vendors to offer a plan for classrooms during flu season. Vendor A offers nightly ULV fogging of every room. Vendor B offers electrostatic spraying of often-touched zones twice a week, after the custodians wipe. Vendor C offers a UV-C robot to run in each classroom overnight.
The district's facilities director asks each vendor the same questions. Vendor A's product label lists wiping and spraying but does not mention fogging. The vendor cannot point to label wording for the method. Vendor B's product label includes electrostatic directions. The vendor explains how workers come at desks from several sides and confirm the wet time. Vendor C's robot has safety shutoffs. But the vendor admits that desk undersides and chair backs sit in shadow and that the robot does not replace cleaning.
The director chooses Vendor B for the often-touched zones and strengthens the custodians' wiping routine. She keeps notes on why she turned down the other two. That way she can explain the choice to the school board and look at it again next season.
What a vendor should be able to show you
A vendor you can trust should hand you the product label with the directions for their method highlighted. They should give you the safety data sheet, which is the maker's fact sheet on hazards. They should describe what cleaning they expect first and give you a written re-entry plan. They should explain their equipment's droplets or light dose in plain words and tell you how workers are trained.
Proof from peer-reviewed studies or outside testing is a plus. But check if the study conditions look like your space. A result from a sealed lab chamber or an intensive care unit may not carry over to your open-plan office or gym.
Last, ask about downtime and what the device needs to run. The best technology on paper is a poor fit if it closes your space longer than you can afford. It is also a poor fit if it needs conditions your building cannot meet. Your state pesticide regulatory agency can tell you if any license or notice rules apply to the method in your area.
- The product label, with the directions for the method highlighted.
- The safety data sheet for the product.
- What cleaning they expect first, in writing.
- A re-entry plan tied to the label.
- Records of worker training and equipment upkeep.
- Proof from settings like yours.
Keeping technology in perspective
Every device described here rests on the same base. That base is cleaning first, a product labeled for the method, enough wet time, and safe re-entry. Technology can extend what a careful crew does. It cannot rescue a careless one.
When a quote leads with the machine and not the plan, steer the talk back. Ask what problem you are solving, where your risk really is, and how you will know the service worked. The answers will tell you if the technology fits your building or just looks good in photos.
It also helps to try it out before you commit. A short trial in one area, with clear goals and honest reporting, will tell you more about how a device works in your building than any sales demo. Ask the vendor to agree to a trial with a set end date and a review meeting. Ask them to put in writing what will be measured and how.



